Room Tone: What ACX Requires and Why Digital Silence Fails
Room tone is one of the few ACX requirements that trips up people who have done everything else right. The file sounds clean, the levels are correct, and it still comes back — because the silence is the wrong kind of silence.
What room tone is
Room tone is the sound of your recording space with nobody speaking. Not an absence of sound: the actual, very quiet presence of the room — the air, the faint hum of the building, whatever makes your space sound like a place rather than a void.
Every room has one. It is what you hear when you stop talking and listen.
What ACX asks for
| Position | Required room tone |
|---|---|
| Start of each file | 0.5 to 1 second before the first word |
| End of each file | 1 to 5 seconds after the last word |
The tail is longer than the head because listeners need a moment to register that a chapter has ended before the next one begins.
Why digital silence fails
Digital silence is a flat line at zero — literally no signal. It is what you get when you select a region and hit Silence, or when a noise gate closes completely.
It fails for a reason you can hear once you know to listen for it. Speech in a room carries the room’s ambience underneath it. When the words stop and the signal drops to absolute zero, the ambience vanishes instantly. That abrupt disappearance registers as a small click, suck or swell — the ear notices the room being switched off.
Across a ten-hour audiobook with a few hundred chapter boundaries and edit points, it becomes genuinely distracting. ACX reviewers listen for it because listeners complain about it.
How to capture room tone properly
- Record it at the start of every session. Press record, sit still, say nothing for thirty seconds. Do not move, do not adjust your chair, do not breathe towards the microphone.
- Do it in the same conditions as the narration. Same microphone position, same gain, same air conditioning state, same door open or closed. Room tone from a different session may not match.
- Label it clearly so you can find it when editing.
Thirty seconds gives you plenty to work with. You will paste short pieces of it wherever you need silence.
Using it in the edit
When you cut out a stumble, a cough or a long pause, you are left with a gap. Fill the gap with room tone rather than silence. Most editors let you paste a looped region; some have a dedicated room tone or ambience fill.
At chapter heads and tails, trim so there is the required amount of tone and no more. Too much tail — more than five seconds — fails just as a missing tail does.
One practical caution: if you loop a short piece of room tone, loop at least a second or two. A very short loop can produce an audible repeating pattern, especially if the tone contains any pitched component.
The noise gate problem
This is where most digital silence comes from. A gate silences everything below a threshold, which is exactly what you do not want in audiobook work.
Gates remove room tone between every phrase, not just at chapter boundaries, and they clip the natural decay from the ends of words. The result is a voice that seems to be switching on and off. It is one of the most recognisable signatures of an inexperienced edit, and it is a reliable rejection.
Use no gate. Clean the noise floor properly instead — our guide to fixing a noise floor that fails ACX covers how.
If your room tone is too loud
Room tone has to be present and below −60 dB RMS. If yours is louder than that, you cannot solve it by replacing it with silence — that just swaps one rejection for another.
The answer is to make the room quieter at the source, then capture clean tone from the improved room. Reducing the tone in post with heavy processing produces an unnatural, filtered-sounding ambience that does not match the ambience under the speech, which is its own kind of obvious.
A quick checklist
- Thirty seconds of room tone recorded at the start of every session
- 0.5–1 second at the head of every file
- 1–5 seconds at the tail of every file
- Gaps filled with tone, never with silence
- No noise gate anywhere in the chain
- Tone measured below −60 dB RMS
The full technical specification is in our guide to ACX audio requirements. If you would rather not manage it chapter by chapter, our audiobook editing service handles room tone, levels and mastering across the whole title so every file matches.





